Fiber Drawing Machine – Consider This..

This automatic optical Fiber tensile testing program is made for operator skill independent utilization in creation and lab configurations. Two basic design configurations enable the consumer to pick between a set up for standard linear Proof screening and with extra mandrels for rotary higher power testing.

The linear edition is made for creation Proof testing with causes as much as 22 N. Motor-driven clamps with carefully designed rubberized inserts ensure that the Fiber Coloring Machine is not really ruined in the testing procedure whilst concurrently eliminating the necessity for an external air provide. Amounts of tugging force, pulling speed and hold time are programmable and conveniently accessible to the operator from the built-in Liquid crystal display touch-screen control. Data from assessments can be stored and reached via the Universal serial bus port or Ethernet user interface.

Mandrels of the identical design as in NYFORS’ optical Fiber recoaters can be installed on the Proof tester within the rotary high strength configuration. The Fiber is wrapped across the two mandrels which assistance it having a special clamping system. By doing this greater lots can be used to the Fiber, allowing breaking up strength assessments below managed circumstances.

Changeable clamp positioning facilitates testing using the highest force levels as well as screening of brief Fiber measures. The compact and light weight design helps make the instrument easy to move around in a laboratory environment and to incorporate in a production work table where space are at reasonably limited. The machine is actually a compact and lightweight tool perfect for screening the potency of visual fibers approximately 30 N. The machine is developed to fulfill all types of programs where a strength test needs to be performed.

The machine is made using the user in mind. The Optical Fiber Ribbon Machine is definitely positioned in the carefully guided linear clamps, and also the screening begins automatically having a “One Touch” go switch. The built-in microprocessor controls all of the important guidelines like tugging force, tugging speed and hold time. This permits to get a totally controlled check each time.

The device can be attached to an outside Computer, which enables access to all programmable guidelines and configurations. The equipment is adapted to stand-on your own use or to the incorporation into different subsystems. The device has an extensive capacity for signing and conserving information including tugging force, tugging speed and Fiber diameter and other parameters.

Two recoat injector configurations can be purchased. The PTR307 utilizes a computerized pump to inject the recoat materials. The amount of material dispensed from the automated injector is controlled by hand using the top-mounted “Inject” switch or programmed into the machine utilizing the tablet pc controller. The PTR307B includes a manual recoat injection program that requires the consumer to personally dispense the recoat material in to the mold cavity; a substitute injector for your PTR307B recoater can be obtained below. Please note that the automated injector is just suitable for higher-directory recoat material, while the handbook injector works with both reduced- and- index recoat material; both are marketed separately below. Make sure you get in touch with Technology Assistance for additional information.

he manual injector can be mounted to compatible Fiber recoaters using the 4-40 anchoring screws on the recoater housing (see photo for the right). Utilize a 3/32″ hex key to safe the injector before use. To get in touch the PTRRRM towards the recoater mold, tighten up the connector at the end of the green plastic tubing, then release by a 1/4 choose allow for rotation.

The injector is equipped with a syndication valve and 2-place selection lever for directing the flow of recoat material. A knurled dispensing attach having an internal plunger behaves as a syringe for the recoat materials. To fill the syringe, point the lever downwards (i.e., towards the recoat container), then spin the knurled dispensing screw counterclockwise until it rotates freely to fill up the syringe (shown in the picture for the right). Then, to inject the recoat material into the mold, point the handle horizontally (i.e., dealing with qyjflh knurled attach) and rotate the attach clockwise until close to the finish in the travel range is reached. Steer clear of bottoming out the dispenser as this may harm the inner plunger; also be mindful when re-engaging the threads to avoid go across threading the dispensing attach. Several fill/inject steps may be required till air is displaced inside the program. Use lens cells plus an acetone or alcohol cleaning solution to gather SZ Stranding Line material that flows through the mold.

Leave a Reply

Your email address will not be published. Required fields are marked *